? semiconductor components industries, llc, 2013 april, 2013 ? rev. 8 1 publication order number: mc14017b/d mc14017b decade counter the mc14017b is a five ? stage johnson decade counter with built ? in code converter. high speed operation and spike ? free outputs are obtained by use of a johnson decade counter design. the ten decoded outputs are normally low, and go high only at their appropriate decimal time period. the output changes occur on the positive ? going edge of the clock pulse. this part can be used in frequency division applications as well as decade counter or decimal decode display applications. features ? fully static operation ? dc clock input circuit allows slow rise times ? carry out output for cascading ? divide ? by ? n counting ? supply voltage range = 3.0 vdc to 18 vdc ? capable of driving two low ? power ttl loads or one low ? power schottky ttl load over the rated temperature range ? pin ? for ? pin replacement for cd4017b ? triple diode protection on all inputs ? these devices are pb ? free and are rohs compliant ? nlv prefix for automotive and other applications requiring unique site and control change requirements; aec ? q100 qualified and ppap capable maximum ratings (voltages referenced to v ss ) symbol parameter value unit v dd dc supply voltage range ? 0.5 to +18.0 v v in , v out input or output voltage range (dc or transient) ? 0.5 to v dd + 0.5 v i in , i out input or output current (dc or transient) per pin 10 ma p d power dissipation, per package (note 1) 500 mw t a ambient temperature range ? 55 to +125 c t stg storage temperature range ? 65 to +150 c t l lead temperature (8 ? second soldering) 260 c stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above the recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may affect device reliability. 1. temperature derating: plastic ?p and d/dw? packages: ? 7.0 mw/ c from 65 c to 125 c this device contains protection circuitry to guard against damage due to high static voltages or electric fields. however, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high ? impedance circuit. for proper operation, v in and v out should be constrained to the range v ss (v in or v out ) v dd . unused inputs must always be tied to an appropriate logic voltage level (e.g., either v ss or v dd ). unused outputs must be left open. http://onsemi.com marking diagrams pdip ? 16 p suffix case 648 mc14017bcp awlyywwg soic ? 16 d suffix case 751b 14017bg awlyww a = assembly location wl, l = wafer lot yy, y = year ww, w = work week g = pb ? free indicator see detailed ordering and shipping information in the package dimensions section on page 3 of this data sheet. ordering information 16 1 1 16
mc14017b http://onsemi.com 2 block diagram functional truth table (positive logic) clock decode clock enable reset output=n 0x0 n x10 n xx1 q0 0 0 n+1 x0 n x0n 1 0 n+1 x = don?t care. if n < 5 carry = ?1?, otherwise = ?0?. clock clock enable reset 14 13 15 c out q9 q8 q7 q6 q5 q4 q3 q2 q1 q0 3 2 4 7 10 1 5 6 9 11 12 v dd = pin 16 v ss = pin 8 logic diagram clock clock enable carry reset q5 q1 q7 q3 q9 11 7 6 2 1 12 q0 q6 q2 q3 q4 354910 14 13 15 c c d rr q q pin assignment 13 14 15 16 9 10 11 12 5 4 3 2 1 8 7 6 c out ce clock reset v dd q8 q4 q9 q2 q0 q1 q5 v ss q3 q7 q6 c c d rr q q c c d rr q q c c d rr q q c c d rr q q
mc14017b http://onsemi.com 3 ????????????????????????????????? ????????????????????????????????? (voltages referenced to v ss ) ?????????? ?????????? ?????????? ?????????? characteristic ???? ???? ???? ???? ??? ??? ??? ??? ????? ????? ? 55 c ????????? ????????? c ????? ????? c ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ???? ???? ???? ??? ??? ??? (note 2) ???? ???? ???? max ??? ??? ??? ??? ??? ??? ?????????? ?????????? ?????????? ?????????? ?????????? output voltage ?0? level v in = v dd or 0 ?1? level v in = 0 or v dd ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ???? ???? ???? ??? ??? ??? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ???? ???? ???? ??? ??? ??? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ?????????? ?????????? ?????????? ?????????? ?????????? ?????????? ?????????? ???? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ???? ???? ???? ???? ??? ??? ??? ??? ???? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ???? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ???? ???? ???? ???? ??? ??? ??? ??? ???? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ?????????? ?????????? ?????????? ?????????? ?????????? ?????????? ?????????? ???? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ???? ???? ???? ???? ??? ??? ??? ??? ???? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ???? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ???? ???? ???? ???? ??? ??? ??? ??? ???? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ??? ?????????? ?????????? ???? ???? ??? ??? ??? ??? ??? ??? 0.1 ???? ???? ??? ??? 0.00001 ???? ???? 0.1 ??? ??? ??? ??? 1.0 ??? ??? adc ?????????? ?????????? ???? ???? ??? ??? ??? ??? ??? ??? ???? ???? ??? ??? ???? ???? ??? ??? ??? ??? ??? ??? ?????????? ?????????? ?????????? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? ???? ???? ???? ??? ??? ??? ???? ???? ???? ??? ??? ??? ??? ??? ??? ??? ??? ??? adc ?????????? ?????????? ?????????? ?????????? ?????????? ???? ???? ???? ???? ???? ??? ??? ??? ??? ??? ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? a/khz) f + i dd i t = (0.55 a/khz) f + i dd i t = (0.83 a/khz) f + i dd ??? ??? ??? ??? ??? adc 2. data labelled ?typ? is not to be used for design purposes but is intended as an indication of the ic?s potential performance. 3. the formulas given are for the typical characteristics only at 25 c. 4. to calculate total supply current at loads other than 50 pf: i t (c l ) = i t (50 pf) + (c l ? 50) vfk where: i t is in a (per package), c l in pf, v = (v dd ? v ss ) in volts, f in khz is input frequency, and k = 0.0011. ordering information device package shipping ? mc14017bcpg pdip ? 16 (pb ? free) 500 units / rail mc14017bdg soic ? 16 48 units / rail NLV14017BDG* mc14017bdr2g soic ? 16 (pb ? free) 2500 units / tape & reel nlv14017bdr2g* ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d. *nlv prefix for automotive and other applications requiring unique site and control change requirements; aec ? q100 qualified and ppap capable.
mc14017b http://onsemi.com 4 ????????????????????????????????? ????????????????????????????????? (note 5) (c l = 50 pf, t a = 25 c) ??????????????? ??????????????? ??????????????? characteristic ????? ????? ????? ???? ???? ???? ???? ???? ???? ???? ???? ???? (note 6) ???? ???? ???? max ??? ??? ??? ??????????????? ??????????????? ??????????????? output rise and fall time t tlh , t thl = (1.5 ns/pf) c l + 25 ns t tlh , t thl = (0.75 ns/pf) c l + 12.5 ns t tlh , t thl = (0.55 ns/pf) c l + 9.5 ns ????? ????? ????? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ??? ??? ??? ??????????????? ??????????????? ??????????????? ??????????????? ??????????????? ????? ????? ????? ????? ????? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ??? ??? ??? ??? ??? ??????????????? ??????????????? ??????????????? ??????????????? ??????????????? ????? ????? ????? ????? ????? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ??? ??? ??? ??? ??? ??????????????? ??????????????? ??????????????? ??????????????? ????? ????? ????? ????? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ??? ??? ??? ??? ??????????????? ??????????????? ??????????????? ??????????????? ??????????????? ? off delay time reset to c out t plh = (1.7 ns/pf) c l + 315 ns t plh = (0.66 ns/pf) c l + 142 ns t plh = (0.5 ns/pf) c l + 100 ns ????? ????? ????? ????? ????? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ??? ??? ??? ??? ??? ??????????????? ??????????????? ??????????????? ????? ????? ????? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ??? ??? ??? ??????????????? ??????????????? ??????????????? ??????????????? ????? ????? ????? ????? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ??? ??? ??? ??? ??????????????? ??????????????? ??????????????? ????? ????? ????? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ??? ??? ??? ??????????????? ??????????????? ??????????????? ????? ????? ????? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ??? ??? ??? ??????????????? ??????????????? ??????????????? ??????????????? ????? ????? ????? ????? ???? ???? ???? ???? ?????????? ?????????? ?????????? ?????????? ??? ??? ??? ??? ??????????????? ??????????????? ??????????????? ????? ????? ????? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ??? ??? ??? ??????????????? ??????????????? ??????????????? ????? ????? ????? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ???? ??? ??? ??? c. 6. data labelled ?typ? is not to be used for design purposes but is intended as an indication of the ic?s potential performance.
mc14017b http://onsemi.com 5 figure 1. typical output source and output sink characteristics test circuit v dd v out v ss v dd v ss s1 s1 a b v ss i d external power supply clock enable reset clock c out q0 q1 q2 q3 q4 q5 q6 q7 q8 q9 output sink drive output source drive decode outputs clock to desired outputs (s1 to b) (s1 to a) carry clock to 5 thru 9 (s1 to b) s1 to a v gs = ? v dd v dd v ds =v out ? v dd v out figure 2. typical power dissipation test circuit v dd v ss i d clock enable reset clock c out q0 q1 q2 q3 q4 q5 q6 q7 q8 q9 500 f 0.01 f ceramic pulse generator f c c l c l c l c l c l c l c l c l c l c l c l
mc14017b http://onsemi.com 6 applications information figure 3 shows a technique for extending the number of decoded output states for the mc14017b. decoded outputs are sequential within each stage and from stage to stage, with no dead time (except propagation delay). figure 3. counter expansion reset clock ce mc14017b q0 q1 q8 q9 ??? 9 decoded outputs clock first stage intermediate stages last stage reset clock ce mc14017b q0q1 q8 q9 ??? reset clock ce mc14017b q1 q8 q9 ??? 8 decoded outputs 8 decoded outputs figure 4. ac measurement definition and functional waveforms pcp ncp clock clock enable t rem reset 20 ns q0 q1 q2 q3 q4 q5 q6 q7 q8 q9 c out t phl t phl t plh t plh t plh t plh t plh t plh t thl t thl t tlh t plh t plh t plh t tlh t plh t phl t phl t phl t phl 50% t phl t phl 90% 10% t thl t phl t thl t phl t thl t tlh t thl t phl t rem t su 20 ns 20 ns 20 ns 20 ns t plh 90% 10% 50% t tlh t tlh t tlh t tlh t tlh t thl t thl t thl t thl t phl t thl 90% 50% 10% 20 ns t plh t tlh v dd v ss v dd v ss v dd v ss v oh v ol v oh v ol v oh v ol v oh v ol v oh v ol v oh v ol v oh v ol v oh v ol v oh v ol v oh v ol v oh v ol
mc14017b http://onsemi.com 7 package dimensions pdip ? 16 p suffix plastic dip package case 648 ? 08 issue t notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. dimension l to center of leads when formed parallel. 4. dimension b does not include mold flash. 5. rounded corners optional. ? a ? b f c s h g d j l m 16 pl seating 18 9 16 k plane ? t ? m a m 0.25 (0.010) t dim min max min max millimeters inches a 0.740 0.770 18.80 19.55 b 0.250 0.270 6.35 6.85 c 0.145 0.175 3.69 4.44 d 0.015 0.021 0.39 0.53 f 0.040 0.70 1.02 1.77 g 0.100 bsc 2.54 bsc h 0.050 bsc 1.27 bsc j 0.008 0.015 0.21 0.38 k 0.110 0.130 2.80 3.30 l 0.295 0.305 7.50 7.74 m 0 10 0 10 s 0.020 0.040 0.51 1.01
mc14017b http://onsemi.com 8 package dimensions soic ? 16 d suffix plastic soic package case 751b ? 05 issue k notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. 18 16 9 seating plane f j m r x 45 g 8 pl p ? b ? ? a ? m 0.25 (0.010) b s ? t ? d k c 16 pl s b m 0.25 (0.010) a s t dim min max min max inches millimeters a 9.80 10.00 0.386 0.393 b 3.80 4.00 0.150 0.157 c 1.35 1.75 0.054 0.068 d 0.35 0.49 0.014 0.019 f 0.40 1.25 0.016 0.049 g 1.27 bsc 0.050 bsc j 0.19 0.25 0.008 0.009 k 0.10 0.25 0.004 0.009 m 0 7 0 7 p 5.80 6.20 0.229 0.244 r 0.25 0.50 0.010 0.019 6.40 16x 0.58 16x 1.12 1.27 dimensions: millimeters 1 pitch soldering footprint 16 89 8x on semiconductor and are registered trademarks of semiconductor co mponents industries, llc (scillc). scillc owns the rights to a numb er of patents, trademarks, copyrights, trade secrets, and other intellectual property. a list ing of scillc?s product/patent coverage may be accessed at ww w.onsemi.com/site/pdf/patent ? marking.pdf. scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and s pecifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. all operating parame ters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or a uthorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in whic h the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or us e scillc products for any such unintended or unauthorized appli cation, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unin tended or unauthorized use, even if such claim alleges that scil lc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyrig ht laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 mc14017b/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative
|
